Seco-Larm E-9679-8B190Q Indoor/Outdoor Long Range Barrier Sensor, 190ft

4.9 (69 items)

Limited Time Sale

Until the end

New $814.81 (tax included) Number of stocks: 1

Used $244.44 (tax included) New Arrivals and Restocks Number in stock: 1

$570.37 cheaper than the new price!!

Free shipping for purchases over $99 ( Details )
Free cash-on-delivery fees for purchases over $99

Other shops (12) $99 ~

See all stores

Please note that the sales price and tax displayed may differ between online and in-store. Also, the product may be out of stock in-store.

New $814.81

Product details

Management number	205070357	Release Date	2025/10/16	List Price	$244.44	Model Number	205070357
Category	Access Control Access Control Accessories

ENFORCER Long-Range Barrier Sensors are ideal for protecting indoor or outdoor areas separated by long distances. They feature reliable photobeam technology with a choice of four programmable beam frequencies that provide superior perimeter protection by eliminating crosstalk and interference when multiple units are used. False alarms caused by animals, falling leaves, poor weather, or other sources are minimized by programming the alarm output trigger operation.

Weatherproof (IP65) for indoor or outdoor perimeter security
Long sensor range up to 190ft (60m) outdoors, 380ft (120m) indoors
Install on windows, doorways, skylights, fence tops, and any place where space is limited
End caps swivel so sensor can be mounted on a single wall or on opposite walls
Programmable immediate trigger on simultaneous breaking of beams, or trigger after a single pair of beams is broken for at least 2 seconds
Heater for use in cold weather operation
Heater activates at 41ºF (5ºC)
Terminal block wiring
Slim design: 2-1/4″ x 1-7/8″ (55 x 49 mm)
Rugged aluminum construction
Built-in tamper switches, one on either end, trigger the alarm if end cap is removed
No synchronizing wires required to align the beams
Form C relay output
LED and buzzer alignment indicators
AGC (Auto Gain Control) circuits regulate beam signals in order to compensate for and ensure operation in rain, fog, and low-temperature conditions
Programmable for 4 different frequencies to reduce interference between multiple units

Specifications

Type	Long-Range Barrier Sensors for Indoor/Outdoor Access Control – Up to 380ft (120m)
Number of Beams	8 pairs
Sensing Range	Outdoor- 190′ (60m), Indoor- 380′ (120m)
Buzzer Active Current	20mA@12VDC (RX)
Heater Active Current	160mA@12VDC
Rx Standby Current	(Buzzer off) 108mA, Heater off,+/-25%@12VDC
Rx Trigger Current	(Buzzer on) 108mA, Heater off,+/-25%@12VDC
Tx Standby & Active Current	109mA, Heater off, +/-25%@12VDC
Input voltage	12~24 VDC
Operating Voltage	12~24VDC
Reaction time	150/300/450/600 ms (DIP switch programmable)
LEDs – Red	Alignment LED (Rx only), ON – beam is broken / OFF – aligned
Detection System	Triggers as programmed when any 2 adjacent pair of beams are broken, or any single pair of beams is broken for over 2 sec. (programmable by JP2)
Alarm Output	NO/NC/COM, relay output, active for 1 sec. when triggered
Tamper Output	1A@120VAC / 1A@24VDC (Tx & Rx)
Case material	Aluminum housing / PC anti-UV cover / ABS end caps
Operating Humidity	0~95%
Operating Temperature	-49º~131º F (-45º~55º C)
Dimensions	1-7/8″ x 2-1/4″ (49 x 55 mm) [Width x Height]
Alignment Angle	Horizontal +/-90º
Weight	14.3-lb (6.5kg) [with brackets]
Enclosure	Weatherproof IP65
Length	79″ (201cm)

Troubleshooting

Receiver LED never turns ON and the buzzer never sounds	Test the power and ground wire with a voltage meter to ensure power is connected and is of the correct voltage
Buzzer does not sound if the sensor is triggered	-If jumper J1 is plugged in, this indicates that the beams are not aligned -If jumper J1 is not plugged in, buzzer should never sound
Receiver LED is ON and the buzzer sounds all the time	Realign the transmitter and receiver
Does not trigger when beam is broken	-Remount the curtain sensor, or repaint the surface to cut down on reflection -Lower the response time (SW1)
Receiver continuously triggers the alarm	-Realign the transmitter and receiver -Check that the tamper switch and the cover for the tamper switch are mounted correctly
False alarm	-Reinstall so that one sensor does not interfere with another sensor -Cut back on leafy vegetation -Do not mount under the edge of the roof -Mount under a roof or shelter